Beacon Hill: Roof and Tower

4 Comments

Mansard Roof

Now that I have most of the lighting done, it’s time to tackle the roof. Looks complicated but is not.

img_7095

I notice that the kitchen side of this dollhouse is rarely photographed, so I’m trying to put out as many pics of it as I can, in case this helps other builders. This is the kitchen side with bay window on, bay window roof temporarily in place (I’m going to cover it with copper). Ready to put on the main roof.

img_7098

The mansard roof pieces are very thin, and bend back into place. The instructions with the kit are pretty good on this. I put glue all over the roof supports (see pic above for the supports), and on the bottom of the mansard piece and the top. Masking tape helps everything stay while the glue dries. (The window sill is there because I had to wire in the lamp before I put on the roof).

img_7099 img_7100

Putting the mansard roof piece on the front. Tacks help a little, but tape is best.

img_7106

Finished mansard roof on the kitchen side (there are only two sides to the roof on the kitchen half of the house). The brown stripe on it is me testing whether the color of stain will work (it’s Early American from Minwax).

img_7151

I’m using shingle strips for this house. Best to stain first.

img_7105

Before I put the roof pieces on, I traced them onto very thin cardboard. I’ll shingle the cardboard then glue the whole thing to the roof. Marked where the shingles strips will fall.

img_7107

Shingling begun. I found out (the hard way) that it’s better to cut the shingle pieces to length first than to try to cut out the hole in the middle for the window after gluing. Live and learn.

img_7149

The finished shingle sheets glued to the mansard roof. The ugly edges will be covered with trim.

Now for the Tower!

The tower is, in the kit, enclosed on four sides, but open on its bottom, so you could hang a chandelier from the very top and have it hang down to the third floor hall. Cool. But, of course, I wanted to change it.

I am interested in astronomy, so decided I’d create a little observatory up there. That means I need a floor for the tower and also to open one of the walls so we can see in. Already found a telescope for it.

img_7114

This is the back wall, which I will cut for the opening into the tower.

img_7115

The piece cut.

img_7119

The four tower walls assembled–the walls each have a large tab on their bottom edge that slide into the large square opening in the tower base (ignore the small slots for the moment).

img_7120

Because I want this to be a room, I had to put a floor back in. I took the piece that I punched out of the middle of the tower base and trimmed it down to slide it back in. You have to take out that piece at first, because the walls fit inside the opening it leaves behind.

 

img_7124

This is the underside of the tower. I have to cover the crease of the fitted-in floor piece and also support it. I cut four strips of 1/2″ wide wood and glued it on the seam of the floor on the underside of the tower (which will be the third-floor ceiling), using the decorative squares to make it look pretty.

img_7131

Here is the underside of the tower painted and ready to go.

img_7122

I went ahead and wallpapered the inside, because I knew I’d never fit the paper after finishing the tower. The floor will be covered with flooring later.

 

img_7136

I also wanted to hang a light in the third floor hall. This is an old light I had in the Big House, in the attic. I worried that it would be too long for the lower ceilings of this house, but the tower pokes up above the ceiling height of the third floor. Perfect!

img_7123

The tower on, ready to be glued in place. The instructions have you finish the roof first, but I wanted to wire in the light, and I couldn’t put the trim piece on until the wiring was done, but you have to put the trim piece on to support the roof sides. Clear? (Took me a while to figure out the sequence–cut wall, glue tower together, insert floor, support floor, put in light, glue tower to house top, run tape wire to tower, wire light, put on trim, do the roof … whew!)

img_7140

Here, I’ve extended the tape wire to the tower room and wired in the lamp. Then I glued on the trim (a solid piece that goes around the four sides), which I painted first.

img_7144

Let there be light! It works! Yay!!!

img_7137

Here’s another departure. I didn’t want to put on the tower roof, because I want to be able to look down into the room–plus the tiny telescope users will want to tilt their refractor high and look at Orion and the Pleiades and find the Andromeda galaxy (I can never see that thing).

I wanted to use the roof trim, but not the roof top. The problem is, though, that the roof sits down on tabs, and if I didn’t use the roof top, the trim didn’t have a smooth surface to rest on. Rather than try to cut off the tabs, which would be difficult at this point, I used 1/8 square strips to even out the edges.

img_7147

Now to put the roof pieces on the tower, which is exactly like putting the mansard pieces on the house. I have lots of tape and clamps to help out.

img_7148

So, now the tower and its roof are on.

img_7150

I am now in the process of putting on the shingles, again gluing them to very thin cardboard pieces, which will then be glued to the mansard roof.

Next time–trimming!! We’re getting there!

 

Advertisements

Beacon Hill–Progress

5 Comments

I took some time away from building the exterior of the Beacon Hill to install more lights. Here’s one I made from jewelry findings from JAF / JAR plus the remnants of a Victorian chandelier I had hanging in The Big House.

img_7036

This was my first attempt to do a light without following instructions–I based it on ones I’d already done but adapted the findings for what I needed. The glass globes came off the old chandelier.

img_7082

I like how it turned out!

img_7080

Next, I finished the first-floor staircase by building a false door which looks like it leads either down to a basement or to a closet.

img_7075

Since I finished and wired the chandelier in the second-floor hallway, I was able to install flooring and the third floor landing railing.

img_7076

Another look at the second floor staircase and new chandelier.

img_7067

When I was in my yard, I noticed this perspective of the house through the window. I like how it looks, so now I’m contemplating leaving this side open. Of course, I’d loose wall space for furniture, but I’ll think about it.

img_7086

I wanted to put a lamp in the third floor room that will be a bedroom. I’d made this lamp some time ago just to see if I could, but had nowhere to put it. I had to find the window sill for the dormer window in the kit and finish it so I could wire the lamp through the sill and wire it in before I put on the roof.

I still have two more lights to do (kitchen and third floor hall), but I can put those in later.

img_7090

And of course, my assistants help with everything.

%d bloggers like this: